Dakle...kak natjerati mdk 10.1 da prpozna ht-ov adsl usb modem ? i da actually radi ?

thnx unaprijed

Odi na tportal.hr http://www.tportal.hr/maxadsl/fset.html
i potraži maxadsl za Linux. Valjda će ti pomoći.

da....kad bi to acutally radilo :/

Citat:
I tako stavio ja Fedoru Core 4...
Imam ovaj usb modem od maxadsl-a (zapravo sam preko iskona) i napravio sam sve kako piše u ovim uputama, ali naravno to ne radi
Dakle, pitam ja vas sad, da li to inace ne radi na Fedori ili sam nešto fulao u konfiguraciji?

Evo ovako sam podesio setup za rp-pppoe-3.5


--------------------------------------------------------------------


[root@localhost Desktop]# cd rp-pppoe-3.5

[root@localhost rp-pppoe-3.5]# adsl-setup

--

Welcome to the ADSL client setup.

First, I will run some checks on
your system to make sure the PPPoE client is installed properly...

--

The following DSL config was found on your system:

Device: Name:
ppp0 DSLppp0

Please enter the device if you want to configure the present DSL config
(default ppp0) or enter 'n' if you want to create a new one: ppp0

--

LOGIN NAME
Enter your Login Name (default krunosla@iskon-dsl): krunosla@iskon-dsl

--

INTERFACE

Enter the Ethernet interface connected to the ADSL modem

For Solaris, this is likely to be something like /dev/hme0.
For Linux, it will be ethX, where 'X' is a number.
(default eth0): tap0

--

Do you want the link to come up on demand, or stay up continuously?

If you want it to come up on demand, enter the idle time in seconds
after which the link should be dropped. If you want the link to
stay up permanently, enter 'no' (two letters, lower-case.)

NOTE: Demand-activated links do not interact well with dynamic IP
addresses. You may have some problems with demand-activated links.

Enter the demand value (default no): no

--

DNS
Please enter the IP address of your ISP's primary DNS server.

If your ISP claims that 'the server will provide dynamic DNS addresses',
enter 'server' (all lower-case) here.
If you just press enter, I will assume you know what you are doing and not modify your DNS setup.

Enter the DNS information here: 213.191.128.8

Please enter the IP address of your ISP's secondary DNS server.
If you just press enter, I will assume there is only one DNS server.

Enter the secondary DNS server address here: 213.191.128.9

--

PASSWORD
Please enter your Password: *******
Please re-enter your Password: *******

--

USERCTRL
Please enter 'yes' (three letters, lower-case.) if you want to allow normal user to start or stop DSL connection (default yes): yes

--

FIREWALLING
Please choose the firewall rules to use. Note that these rules are very basic. You are strongly encouraged to use a more sophisticated firewall setup; however, these will provide basic security. If you are running any servers on your machine, you must choose 'NONE' and set up firewalling yourself. Otherwise, the firewall rules will deny access to all standard servers like Web, e-mail, ftp, etc. If you are using SSH, the rules will block outgoing SSH connections which allocate a privileged source port.

The firewall choices are:

0 - NONE: This script will not set any firewall rules. You are responsible for ensuring the security of your machine. You are STRONGLY recommended to use some kind of firewall rules.
1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation
2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway
for a LAN

Choose a type of firewall (0-2): 1

--

Start this connection at boot time
Do you want to start this connection at boot time?

Please enter no or yes (default no): no

--

** Summary of what you entered **

Ethernet Interface: tap0
User name: krunosla@iskon-dsl
Activate-on-demand: No
Primary DNS: 213.191.128.8
Secondary DNS: 213.191.128.9
Firewalling: STANDALONE
User Control: yes

--

Accept these settings and adjust configuration files (y/n)? y


Adjusting /etc/sysconfig/network-scripts/ifcfg-ppp0
Adjusting /etc/resolv.conf
Adjusting /etc/ppp/chap-secrets and /etc/ppp/pap-secrets
(But first backing it up to /etc/ppp/chap-secrets.bak)
(But first backing it up to /etc/ppp/pap-secrets.bak)


Congratulations, it should be all set up!


Type '/sbin/ifup ppp0' to bring up your xDSL link and '/sbin/ifdown ppp0' to bring it down.
Type '/sbin/adsl-status/etc/sysconfig/network-scripts/ifcfg-ppp0' to see the link status.

--

[root@localhost rp-pppoe-3.5]#


---------------------------------------------------


Kad hocu pokrenut adsl preko EciAdsl-a uvijek mi zapne na trecem koraku ("synchronization") i nece dalje...
Ovako...

Samo da kazem da su upute od nedavno i ovdje na wiki stavljene.

Ja ti stvarno nemogu pomoci oko ovoga, mozda da kontaktiras autora ili da pogledas dokumentaciju na EciAdsl stranicama
http://eciadsl.flashtux.org/doc.php?file=eciadsl_install&doc_lang=en&view=html
Najcesci uzrok ne uspjevanja sinkronizacije je los .bin file koliko vidim, tamo pise da probas razlicite a ako ni to ne upali da napravis svoj (upute za to su isto tamo).

P.S vidim da pokreces "eciadsl-start", nakon sto si konfigurirao roaring penguin ("adsl-setup"), sto se desi kada pokrenes "adsl-start" ?

Citat:
Evo ovako...



P.S. inače, ja sam isto iz Rijeke

ne valja ti taj gs7470_synch04.bin za eciadsl
ja sam napravio svoj *.bin file (gs7470_synch999.bin) za A-100-i ako hoces posaljem ti ga e-mailom.

-- kad upišem naredbu #eciadsl-start ; sve dobro prođe i piše mi na kraju "waiting for tap0" i ljepo se upale obje lampice tj obavio je trening , a problem je u tome što taj Eciadsl koliko se ja kužim ne koristi PPPoE protokol , pa se mora posebno instalirati rp-pppoe paket koji naravno ne mogu uštimati !

...# eciadsl-config-tk

evo kako izgleda moj eciadsl-config-tk

za chipset GS7470 ide ALTSynch=0 i ALTpppoeci=0
za VPI i VCI nisam siguran da je točan zbog toga što ne znam koji broj zove modem u Windowsima
...# eciadsl-start

za sad sve OK

...# adsl-start

sta se desava kad upisem adsl-start - uglavnom ništa

ne znam u cemu je problem... ako mi netko moze pomoci bio bih VVVVRRRRlo zahvalan;

I ja bi molio jednu kopiju na anrxc[at]hi.t-com.hr , zahvaljujem.

EDIT
Evo ga file ovdje, ako netko bude imao uspjeha sa ovim bin fileom neka nam da do znanja:
http://www.sysphere.org/tmp/gs7470_synch999.tar.gz

Takoder postoji jedan thread na ABCLinux o ovim modemima, oni koriste drukciji driver i stvar navodno radi, svi vi koji ne uspjevate sa EciAdsl, pogledajte:
http://www.abclinuxu.cz/forum/show/72063