Uspio sam naci na netu drivere za d-link g122 u tar.gz i uspjesno instaliram u /opt direktoriju no medjutim sta dalje da radim molim vas pomoc kako da to se sve pokrene?

Koja distribucija?Unutar te tar.gz arhive imas README.txt u kojem obicno pise sta treba raditi.

Distribucija je Ubuntu 9.10 . evo ovo pise

* README

*

* Ralink Tech Inc.

*

* http://www.ralinktech.com

*



=======================================================================

ModelName:

===========

RT73(RT2571W) Wireless Lan Linux Driver





=======================================================================

Driver lName:

===========

rt73





=======================================================================

Supporting Kernel:

===================

linux kernel 2.4 and 2.6 series.

Tested in Redhat 7.3 or later.





=======================================================================

Description:

=============

This is a linux device driver for Ralink RT73 a/b/g WLAN Card.





=======================================================================

Contents:

=============

Makefile.4 : Makefile for kernel 2.4 series

Makefile.6 : Makefile for kernel 2.6 series

*.c : c files

*.h : header files





=======================================================================

Features:

==========

This driver implements basic IEEE802.11. Infrastructure and adhoc mode

with open or shared or WPA-PSK or WPA2-PSK authentication method.

NONE, WEP, TKIP and AES encryption.





=======================================================================

Build Instructions:

====================

1> $tar -xvzf RT73_Linux_STA_Drv_x.x.x.x.tar.gz

go to "./RT73_Linux_STA_Drv_x.x.x.x/Module" directory.



2> $cp Makefile.4 ./Makefile # [kernel 2.4]

or

$cp Makefile.6 ./Makefile # [kernel 2.6]



3> [kernel 2.4]

$chmod 755 Configure

$make config # config build linux os version



4> $make all # compile driver source code



5> $cp rt73.bin /etc/Wireless/RT73STA/ # copy firmware



6> $dos2unix rt73sta.dat

$cp rt73sta.dat /etc/Wireless/RT73STA/rt73sta.dat

# !!!check if it is a binary file before loading !!!



7> $load

#[kernel 2.4]

# $/sbin/insmod rt73.o

# $/sbin/ifconfig rausb0 inet YOUR_IP up



#[kernel 2.6]

# $/sbin/insmod rt73.ko

# $/sbin/ifconfig rausb0 inet YOUR_IP up





=======================================================================

CONFIGURATION:

====================

RT73 driver can be configured via following interfaces,

i.e. (i)"iwconfig" command, (ii)"iwpriv" command, (iii) configuration file

(iv)RaConfig



i) iwconfig comes with kernel.

ii) iwpriv usage, please refer to file "iwpriv_usage.txt" for details.

iii)copy configuration file "rt73sta.dat" to /etc/Wireless/RT73STA/rt73sta.dat.

iv) RaConfig is utility for rt73.



Note:



Configuration File : rt73sta.dat

---------------------------------------

# Copy this file to /etc/Wireless/RT73STA/rt73sta.dat

# This file is a binary file and will be read on loading rt.o module.

#

# Use "vi -b rt73sta.dat" to modify settings according to your need.

#

# 1.) set NetworkType to "Adhoc" for using Adhoc-mode, otherwise using Infrastructure

# 2.) set Channel to "0" for auto-select on Infrastructure mode

# 3.) set SSID for connecting to your Accss-point.

# 4.) AuthMode can be "WEPAUTO", "OPEN", "SHARED", "WPAPSK", "WPA2PSK", "WPANONE"

# 5.) EncrypType can be "NONE", "WEP", "TKIP", "AES"

# for more information refer to the Readme file.

#

# The word of "[Default]" must not be removed

[Default]

CountryRegion=0

CountryRegionABand=7

WirelessMode=0

SSID=AP350

NetworkType=Infra

Channel=0

AuthMode=OPEN

EncrypType=NONE

DefaultKeyID=1

Key1Type=0

Key1Str=0123456789

Key2Type=0

Key2Str=

Key3Type=0

Key3Str=

Key4Type=0

Key4Str=

WPAPSK=abcdefghijklmnopqrstuvwxyz

TxBurst=0

PktAggregate=0

TurboRate=0

WmmCapable=0

AckPolicy1=0

AckPolicy2=0

AckPolicy3=0

AckPolicy4=0

BGProtection=0

ShortSlot=0

IEEE80211H=0

TxRate=0

RTSThreshold=2347

FragThreshold=2346

PSMode=CAM

TxPreamble=0

AdhocOfdm=0



-----------------------------------------------

*NOTE:

WMM parameters

WmmCapable Set it as 1 to turn on WMM Qos support

AckPolicy1~4 Ack policy which support normal Ack or no Ack

(AC_BK, AC_BE, AC_VI, AC_VO)



All WMM parameters do not support iwpriv command but WmmCapable,

please store all parameter to rt73sta.dat, and restart driver.



-----------------------------------------------

syntax is 'Param'='Value' and describes below.



1. CountryRegion=value

value

0: use 1 ~ 11 Channel

1: use 1 ~ 13 Channel

2: use 10, 11 Channel

3: use 10 ~ 13 Channel

4: use 14 Channel

5: use 1 ~ 14 Channel

6: use 3 ~ 9 Channel



2. CountryRegionForABand=value

value

0: use 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165 Channel

1: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 Channel

2: use 36, 40, 44, 48, 52, 56, 60, 64 Channel

3: use 52, 56, 60, 64, 149, 153, 157, 161 Channel

4: use 149, 153, 157, 161, 165 Channel

5: use 149, 153, 157, 161 Channel

6: use 36, 40, 44, 48 Channel

7: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 Channel



3. SSID=value

value

0~z, 1~32 ascii characters.



4. WirelessMode=value

value

0: 11b/g mixed,

1: 11b only,

2: 11a only, //Support in RfIcType=1(id=RFIC_5226) or RfIcType=3(id=RFIC_5225)

3: 11a/b/g mixed, //Support in RfIcType=1(id=RFIC_5226) or RfIcType=3(id=RFIC_5225)

4: 11g only



5. TxRate=value

value

0: Auto //WirelessMode=0~4

1: 1 Mbps //WirelessMode=0 or 1 or 3

2: 2 Mbps //WirelessMode=0 or 1 or 3

3: 5.5 Mbps //WirelessMode=0 or 1 or 3

4: 11 Mbps //WirelessMode=0 or 1 or 3

5: 6 Mbps //WirelessMode=0 or 2 or 3 or 4

6: 9 Mbps //WirelessMode=0 or 2 or 3 or 4

7: 12 Mbps //WirelessMode=0 or 2 or 3 or 4

8: 18 Mbps //WirelessMode=0 or 2 or 3 or 4

9: 24 Mbps //WirelessMode=0 or 2 or 3 or 4

10: 36 Mbps //WirelessMode=0 or 2 or 3 or 4

11: 48 Mbps //WirelessMode=0 or 2 or 3 or 4

12: 54 Mbps //WirelessMode=0 or 2 or 3 or 4



6. Channel=value

value

depends on CountryRegion or CountryRegionForABand



7. BGProtection=value

value

0: Auto

1: Always on

2: Always off



8. TxPreamble=value

value

0: Preamble Long

1: Preamble Short

2: Auto



9. RTSThreshold=value

value

1~2347



10. FragThreshold=value

value

256~2346



11. TxBurst=value

value

0: Disable

1: Enable



12. NetworkType=value

value

Infra: infrastructure mode

Adhoc: adhoc mode



13. AdhocOfdm=value

value

0: WIFI mode (1,2,5.5,11 mbps rates)

1: b/g mixed, (1,2,5.5,11,6,9,12,18,24,36,48,54 mbps rates)

2: 11g only, (6,9,12,18,24,36,48,54 mbps rates)

3: 11a only, (6,9,12,18,24,36,48,54 mbps rates)



14. AuthMode=value

value

OPEN For open system

SHARED For shared key system

WEPAUTO Auto switch between OPEN and SHARED

WPAPSK For WPA pre-shared key (Infra)

WPA2PSK For WPA2 pre-shared key (Infra)

WPANONE For WPA pre-shared key (Adhoc)



15. EncrypType=value

value

NONE For AuthMode=OPEN

WEP For AuthMode=OPEN or SHARED

TKIP For AuthMode=WPAPSK or WPA2PSK or WPANONE

AES For AuthMode=WPAPSK or WPA2PSK or WPANONE



16. DefaultKeyID=value

value

1~4



17. Key1=value

Key2=value

Key3=value

Key4=value

value

10 or 26 hexadecimal characters eg: 012345678

5 or 13 ascii characters eg: passd

(usage : "iwpriv" only)



18. Key1Type=vaule

Key2Type=value

Key3Type=vaule

Key4Type=vaule

value

0 hexadecimal type

1 assic type

(usage : reading profile only)



19. Key1Str=value

Key2Str=value

Key3Str=vaule

Key4Str=vaule

value

10 or 26 characters (key type=0)

5 or 13 characters (key type=1)

(usage : reading profile only)



20. WPAPSK=value

value

8~63 ASCII or

64 HEX characters



21. PSMode=value

value

0: CAM Constantly Awake Mode

1: Max_PSP Max Power Savings

2: Fast_PSP Power Save Mode



22. PktAggregate=value

value

0: Disable

1: Enable when the peer supports it





/-------------------!Not support yet!-----------------------/

23. TurboRate=value

value

0: Disable

1: Enable 72/100 Mbps whenever applicable



24. WmmCapable=value

value

0: Disable WMM

1: Enable WMM



25. IEEE80211H=value

value

0: Disable

1: Enable Spectrum management

(This field can be enable only in A band)

/-------------------!Not support yet!-----------------------/





MORE INFORMATION

=================================================================================

If you want for rt73 driver to auto-load at boot time:

A) choose rausb0 for first RT73 WLAN card, rausb1 for second RT73 WLAN card, etc.



B) create(edit) 'ifcfg-rausb0' file in /etc/sysconfig/network-scripts/,

edit( or add the line) in /etc/modules.conf:

alias rausb0 rt73



C) edit(create) the file /etc/sysconfig/network-scripts/ifcfg-rausb0

DEVICE='rausb0'

ONBOOT='yes'





NOTE:

if you use dhcp, add this line too .

BOOTPROTO='dhcp'



*D) To ease the Default Gateway setting,

add the line

GATEWAY=x.x.x.x

in /etc/sysconfig/network

Umjesto što si bezveze skopirao cijeli README ovdje, mogao si ga pročitati. Sve ti piše u njemu što trebaš raditi da bi ga instalirao, korak po korak, počevši s "Build instructions". Osim ako imaš problema s engleskim, no to je onda druga priča.

Pogledaj ovaj link.

WifiDocsDriverRalinkRT73

Ako ti redame.txt nije dovoljno jasan moras nekad malo vise googlati kad trazis rjesenje masu puta se moze naci tutorijal,how-to.A to nije "vise googlanja" ja sam nakon nekoliko upita u Googlu pronasao ovu dokumentaciju.